Defines related to the CC1350 LaunchPad.
More...
|
file | board.h |
| Header file with definitions related to the I/O connections on the TI CC1350 LaunchPad.
|
|
|
Those values are not meant to be modified by the user
|
#define | LEDS_CONF_COUNT 2 |
|
#define | LEDS_CONF_RED 1 |
|
#define | LEDS_CONF_GREEN 2 |
|
|
Those values are not meant to be modified by the user
|
#define | BOARD_IOID_LED_1 IOID_6 |
|
#define | BOARD_IOID_LED_2 IOID_7 |
|
|
Those values are not meant to be modified by the user
|
#define | BOARD_IOID_UART_RX IOID_2 |
|
#define | BOARD_IOID_UART_TX IOID_3 |
|
#define | BOARD_IOID_UART_RTS IOID_18 |
|
#define | BOARD_IOID_UART_CTS IOID_19 |
|
#define | BOARD_UART_RX (1 << BOARD_IOID_UART_RX) |
|
#define | BOARD_UART_TX (1 << BOARD_IOID_UART_TX) |
|
#define | BOARD_UART_RTS (1 << BOARD_IOID_UART_RTS) |
|
#define | BOARD_UART_CTS (1 << BOARD_IOID_UART_CTS) |
|
|
Those values are not meant to be modified by the user
|
#define | BOARD_IOID_KEY_LEFT IOID_13 |
|
#define | BOARD_IOID_KEY_RIGHT IOID_14 |
|
#define | BOARD_KEY_LEFT (1 << BOARD_IOID_KEY_LEFT) |
|
#define | BOARD_KEY_RIGHT (1 << BOARD_IOID_KEY_RIGHT) |
|
|
#define | BOARD_STRING "TI CC1350 LaunchPad" |
|
Defines related to the CC1350 LaunchPad.
This file provides connectivity information on LEDs, Buttons, UART and other peripherals
This file is not meant to be modified by the user.
◆ BOARD_BUTTON_HAL_INDEX_KEY_LEFT
#define BOARD_BUTTON_HAL_INDEX_KEY_LEFT 0x00 |
Board indices for the button HAL.
Those values are not meant to be modified by the user
Definition at line 203 of file board.h.
◆ BOARD_IOID_CS
#define BOARD_IOID_CS IOID_11 |
Remaining pins.
Those values are not meant to be modified by the user
Definition at line 172 of file board.h.
◆ BOARD_IOID_SCL
#define BOARD_IOID_SCL IOID_4 |
I2C IOID mappings.
Those values are not meant to be modified by the user
Definition at line 131 of file board.h.
◆ CCXXWARE_CONF_BL_PIN_NUMBER
#define CCXXWARE_CONF_BL_PIN_NUMBER BOARD_IOID_KEY_LEFT |
ROM bootloader configuration.
Change CCXXWARE_CONF_BL_PIN_NUMBER to BOARD_IOID_KEY_xyz to select which button triggers the bootloader on reset. Use CCXXWARE_CONF_BL_LEVEL to control the pin level that enables the bootloader (0: low, 1: high). It is also possible to use any other externally-controlled DIO.
Definition at line 162 of file board.h.
◆ PROP_MODE_CONF_TX_POWER_779_930
#define PROP_MODE_CONF_TX_POWER_779_930 tx_power_driver_779_930 |
TX power settings.
Those values are not meant to be modified by the user
Definition at line 150 of file board.h.
◆ RF_SWITCH_CONF_ENABLE
#define RF_SWITCH_CONF_ENABLE 1 |
CC1350LP RF Switch.
Those values are not meant to be modified by the user
Definition at line 141 of file board.h.