Contiki-NG
|
Header file with definitions related to the I/O connections on the TI SmartRF06EB. More...
Go to the source code of this file.
Macros | |
SmartRF LED configuration | |
LEDs on the SmartRF06 (EB and BB) are connected as follows:
LED1 shares the same pin with the USB pullup | |
#define | LEDS_CONF_YELLOW 1 |
#define | LEDS_CONF_GREEN 2 |
#define | LEDS_CONF_ORANGE 4 |
#define | LEDS_ARCH_L1_PORT GPIO_C_NUM |
#define | LEDS_ARCH_L1_PIN 1 |
#define | LEDS_ARCH_L2_PORT GPIO_C_NUM |
#define | LEDS_ARCH_L2_PIN 2 |
#define | LEDS_ARCH_L3_PORT GPIO_C_NUM |
#define | LEDS_ARCH_L3_PIN 3 |
#define | LEDS_ARCH_L4_PORT GPIO_C_NUM |
#define | LEDS_ARCH_L4_PIN 0 |
#define | LEDS_CONF_RED 8 |
#define | LEDS_CONF_COUNT 4 |
USB configuration | |
The USB pullup is driven by PC0 and is shared with LED1 | |
#define | USB_PULLUP_PORT GPIO_C_NUM |
#define | USB_PULLUP_PIN 0 |
UART configuration | |
On the SmartRF06EB, the UART (XDS back channel) is connected to the following ports/pins
We configure the port to use UART0. To use UART1, replace UART0_* with UART1_* below. | |
#define | UART0_RX_PORT GPIO_A_NUM |
#define | UART0_RX_PIN 0 |
#define | UART0_TX_PORT GPIO_A_NUM |
#define | UART0_TX_PIN 1 |
#define | UART1_CTS_PORT GPIO_B_NUM |
#define | UART1_CTS_PIN 0 |
#define | UART1_RTS_PORT GPIO_D_NUM |
#define | UART1_RTS_PIN 3 |
SmartRF Button configuration | |
Buttons on the SmartRF06 are connected as follows:
| |
#define | BUTTON_SELECT_PORT GPIO_A_NUM |
BUTTON_SELECT -> PA3. | |
#define | BUTTON_SELECT_PIN 3 |
#define | BUTTON_SELECT_VECTOR GPIO_A_IRQn |
#define | BUTTON_LEFT_PORT GPIO_C_NUM |
BUTTON_LEFT -> PC4. | |
#define | BUTTON_LEFT_PIN 4 |
#define | BUTTON_LEFT_VECTOR GPIO_C_IRQn |
#define | BUTTON_RIGHT_PORT GPIO_C_NUM |
BUTTON_RIGHT -> PC5. | |
#define | BUTTON_RIGHT_PIN 5 |
#define | BUTTON_RIGHT_VECTOR GPIO_C_IRQn |
#define | BUTTON_UP_PORT GPIO_C_NUM |
BUTTON_UP -> PC6. | |
#define | BUTTON_UP_PIN 6 |
#define | BUTTON_UP_VECTOR GPIO_C_IRQn |
#define | BUTTON_DOWN_PORT GPIO_C_NUM |
BUTTON_DOWN -> PC7. | |
#define | BUTTON_DOWN_PIN 7 |
#define | BUTTON_DOWN_VECTOR GPIO_C_IRQn |
#define | PLATFORM_HAS_BUTTON 1 |
#define | PLATFORM_SUPPORTS_BUTTON_HAL 1 |
ADC configuration | |
These values configure which CC2538 pins and ADC channels to use for the ADC inputs. ADC inputs can only be on port A. | |
#define | ADC_ALS_PWR_PORT GPIO_A_NUM |
ALS power GPIO control port. | |
#define | ADC_ALS_PWR_PIN 7 |
ALS power GPIO control pin. | |
#define | ADC_ALS_OUT_PIN 6 |
ALS output ADC input pin on port A. | |
SPI configuration | |
These values configure which CC2538 pins to use for the SPI lines. Both SPI instances can be used independently by providing the corresponding port / pin macros. | |
#define | SPI0_IN_USE 0 |
#define | SPI1_IN_USE 0 |
CC2538 TSCH configuration | |
#define | RADIO_PHY_OVERHEAD CC2538_PHY_OVERHEAD |
#define | RADIO_BYTE_AIR_TIME CC2538_BYTE_AIR_TIME |
#define | RADIO_DELAY_BEFORE_TX CC2538_DELAY_BEFORE_TX |
#define | RADIO_DELAY_BEFORE_RX CC2538_DELAY_BEFORE_RX |
#define | RADIO_DELAY_BEFORE_DETECT CC2538_DELAY_BEFORE_DETECT |
Device string used on startup | |
#define | BOARD_STRING "TI SmartRF06 + cc2538EM" |
Header file with definitions related to the I/O connections on the TI SmartRF06EB.
Definition in file board.h.